Sumitomo - Полный каталог инструмента - 2016 EN
для заказа - sumitomo@sumitomo-tools.ru
Straight Flute Ball Endmills Spiral Endmills for Non-Ferrous Cutting
BSM 2000 Type ASM 2000 Type
Carbide grade: A1 (Micrograin) Carbide grade: H1 (Micrograin)
Helix angle : 0 R Tolerance (mm) Helix angle : 30
R 5,0 + 0 – 0,015 Corner : Sharp edge
Endmills 5,0 < R 7,5 + 0 – 0,020
7,5 < R + 0 – 0,025 Endmills
Cat. No.
(mm) Cat. No. (mm)
BSM 2010
BSM 2020 Stock R D l L d ASM 2020 Stock D l L d
BSM 2030 ASM 2030
BSM 2040 0,5 1,0 4 40 4 ASM 2040 q 2,0 6 40 4
BSM 2050 s 1,0 2,0 7 40 4 ASM 2050 q 3,0 10 45 6
BSM 2060 ASM 2060 q 4,0 12 45 6
BSM 2080 1,5 3,0 9 45 6 ASM 2080 q 5,0 15 50 6
BSM 2100 s 2,0 4,0 15 45 6 ASM 2100 q 6,0 15 50 6
BSM 2120 s 2,5 5,0 15 50 6 ASM 2120 q 8,0 18 60 8
BSM 2140 s 3,0 6,0 20 50 6 ASM 2160 q 10,0 22 71 10
BSM 2160 s 4,0 8,0 20 60 8 q 12,0 25 75 12
BSM 2200 s 5,0 10,0 20 70 10
s 6,0 12,0 25 75 12 16,0 32 90 16
7,0 14,0 25 90 16
8,0 16,0 35 110 16
10,0 20,0 35 110 20
Uncoated
Endmills
Rcoencdoimtiomnesnded doc =0,3 x D, (Below R1,0 ; 0,2 x D)
woc =Max0,7 x D, (Below R1,0 ; 0,6 x D)
Material Carbon steel, Alloy steel Cast iron Rcoencdoimtiomnesnded (Shoulder processing) doc =1,5 x D
woc =0,1 x D
R (BelowHRC30) (BelowHRC40) (BelowHRC45)
R0,5 ~ vc 40--60 30-40-50 20--40 40-50-60 Material Al-alloy Cast iron
D
R1,25 f t 0,004~0,010 0,004~0,010 0,002~0,005 0,008~0,015
R1,5 ~ vc 40-50-60 30--50 20-30-40 40--60 1~ vc 100-200-300 100-120-150
2,5 f t 0,004~0,017 0,008~0,020
R2,5 f t 0,013~0,025 0,013~0,025 0,007~0,013 0,017~0,042 vc 100-200-300 100-120-150
3~ f t 0,018~0,036 0,027~0,060
R3 ~ vc 40-50-60 30--50 20-30-40 40--60 5 vc 100-200-300 100-120-150
R6 f t 0,038~0,070 0,065~0,157
6~ vc 100-200-300 100-120-150
12 f t 0,075~0,125 0,160~0,250
vc =m/min f t =mm/tooth
f t 0,030~0,050 0,030~0,050 0,017~0,033 0,056~0,136 doc 14 ~
doc16
R6,5 ~ vc 40-50-60 30--50 20--40 40-50-60
R9,5 f t 0,070~0,100 0,070~0,100 0,040~0,057 0,167~0,238 woc D
woc
R10 ~ vc 40-50-60 30-40-50 20-30-40 40-50-60
f t 0,118~0,167 0,118~0,167 0,085~0,095 0,250~0,350
vc =m/min f t =mm/tooth
www.sumitomo-tools.ru J47
для заказа - sumitomo@sumitomo-tools.ru